Eaton MCLA1608V2-8R2-R 8.2 nH Chip Inductor, 10 Q
Eaton MCLA1608V2-8R2-R 8.2 nH Chip Inductor, 10 Q

Eaton MCLA1608V2-8R2-R 8.2 nH Chip Inductor, 10 Q

Share
MCLA1608V2-8R2-R: multilayer chip inductor, 8.2 nH ±5%, Q 10, SRF 4500 MHz, 500 mA, DCR 350 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V2-8R2-R 8.2 nH Chip Inductor, 10 Q

    MCLA1608V2-8R2-R at a glance: multilayer chip inductor, 8.2 nH ±5%, Q 10, SRF 4500 MHz, 500 mA, DCR 350 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCLA1608V2-8R2-R
    Inductance8.2 nH ±5%
    Q minimum10
    DCR maximum @ +25 °C350 mOhm
    Rated current maximum500 mA
    SRF minimum4500 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10976

    Mechanical Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10976; the package column above gives the body size in millimetres.

    Reading the Data Sheet

    Where a circuit needs a small, stable inductance in a package measured in millimetres, the multilayer chip is the default. Its self-resonant frequency is the practical ceiling – above it the part behaves like a capacitor, so the SRF column is the first thing to check against the operating band.

    The row reads 8.2 nH ±5% with a minimum Q of 10 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 10 means the part’s loss is about 10 % of its reactance in that band.

    Self-resonance is quoted as 4500 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 4500 MHz is the design headroom.

    Within the MCLA1608V2 family this is value 12 of 34, in a range that runs from 0.001 to 0.47 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message