Eaton MCLA2012V1-1R5-R 1.5 uH Chip Inductor 0805
Eaton MCLA2012V1-1R5-R 1.5 uH Chip Inductor 0805

Eaton MCLA2012V1-1R5-R 1.5 uH Chip Inductor 0805

Share
MCLA2012V1-1R5-R: multilayer chip inductor, 1.5 uH ±10, Q 35, SRF 60 MHz, 50 mA, DCR 400 mOhm.
    • Product Details
    • Download

    Eaton MCLA2012V1-1R5-R 1.5 uH Chip Inductor 0805

    MCLA2012V1-1R5-R at a glance: multilayer chip inductor, 1.5 uH ±10, Q 35, SRF 60 MHz, 50 mA, DCR 400 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMCLA2012V1-1R5-R
    Inductance1.5 uH ±10
    Q minimum35
    DCR maximum @ +25 °C400 mOhm
    Rated current maximum50 mA
    SRF minimum60 MHz
    Test frequency10 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10977

    Mechanical Dimensions & Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10977; the package column above gives the body size in millimetres.

    The Figures Explained

    Where a circuit needs a small, stable inductance in a package measured in millimetres, the multilayer chip is the default. Its self-resonant frequency is the practical ceiling – above it the part behaves like a capacitor, so the SRF column is the first thing to check against the operating band.

    The row reads 1.5 uH ±10 with a minimum Q of 35 at 10 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 35 means the part’s loss is about 2.86 % of its reactance in that band.

    Self-resonance is quoted as 60 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 60 MHz is the design headroom.

    Within the MCLA2012V1 family this is value 19 of 30, in a range that runs from 0.047 to 12 nH.

    Positioning in the Range

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products