Eaton MCLA2012V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz
Eaton MCLA2012V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz

Eaton MCLA2012V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz

Share
MCLA2012V1-1R8-R: multilayer chip inductor, 1.8 uH ±10, Q 35, SRF 55 MHz, 50 mA, DCR 400 mOhm.
    • Product Details
    • Download

    Eaton MCLA2012V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz

    MCLA2012V1-1R8-R at a glance: multilayer chip inductor, 1.8 uH ±10, Q 35, SRF 55 MHz, 50 mA, DCR 400 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCLA2012V1-1R8-R
    Inductance1.8 uH ±10
    Q minimum35
    DCR maximum @ +25 °C400 mOhm
    Rated current maximum50 mA
    SRF minimum55 MHz
    Test frequency10 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10977

    Mechanical Dimensions & Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10977; the package column above gives the body size in millimetres.

    What the Numbers Mean

    The inductance here is a few nanohenry, which puts the part in RF and high-speed digital territory: matching networks, filter sections, bias chokes on amplifier supplies, and the small isolation inductors that keep clock harmonics out of connectors. The multilayer body keeps the parasitics predictable, and the Q column tells you how much loss the part adds at the test frequency.

    The row reads 1.8 uH ±10 with a minimum Q of 35 at 10 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 35 means the part’s loss is about 2.86 % of its reactance in that band.

    Self-resonance is quoted as 55 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 55 MHz is the design headroom.

    Within the MCLA2012V1 family this is value 20 of 30, in a range that runs from 0.047 to 12 nH.

    Series Positioning

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products