Eaton MCLA3216V1-1R0-R 1.0 uH Chip Inductor 1206
Eaton MCLA3216V1-1R0-R 1.0 uH Chip Inductor 1206

Eaton MCLA3216V1-1R0-R 1.0 uH Chip Inductor 1206

Share
MCLA3216V1-1R0-R: multilayer chip inductor, 1.0 uH ±10, Q 35, SRF 75 MHz, 100 mA, DCR 300 mOhm.
    • Product Details
    • Download

    Eaton MCLA3216V1-1R0-R 1.0 uH Chip Inductor 1206

    MCLA3216V1-1R0-R at a glance: multilayer chip inductor, 1.0 uH ±10, Q 35, SRF 75 MHz, 100 mA, DCR 300 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCLA3216V1-1R0-R
    Inductance1.0 uH ±10
    Q minimum35
    DCR maximum @ +25 °C300 mOhm
    Rated current maximum100 mA
    SRF minimum75 MHz
    Test frequency10 MHz
    Test voltage50 mV
    Package3.2 x 1.6 mm
    Size code3216 (1206)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10978

    Dimensions and Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10978; the package column above gives the body size in millimetres.

    Reading the Data Sheet

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 1.0 uH ±10 with a minimum Q of 35 at 10 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 35 means the part’s loss is about 2.86 % of its reactance in that band.

    Self-resonance is quoted as 75 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 75 MHz is the design headroom.

    Within the MCLA3216V1 family this is value 17 of 30, in a range that runs from 0.047 to 12 nH.

    Series Positioning

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products