Eaton MCQ1V2012-R047-R 0.047 nH Chip Inductor, 25 Q
Eaton MCQ1V2012-R047-R 0.047 nH Chip Inductor, 25 Q

Eaton MCQ1V2012-R047-R 0.047 nH Chip Inductor, 25 Q

Share
MCQ1V2012-R047-R: multilayer chip inductor, 0.047 nH ±10, Q 25, SRF 320 MHz, 300 mA, DCR 150 mOhm.
    • Product Details
    • Download

    Eaton MCQ1V2012-R047-R 0.047 nH Chip Inductor, 25 Q

    MCQ1V2012-R047-R at a glance: multilayer chip inductor, 0.047 nH ±10, Q 25, SRF 320 MHz, 300 mA, DCR 150 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCQ1V2012-R047-R
    Inductance0.047 nH ±10
    Q minimum25
    DCR maximum @ +25 °C150 mOhm
    Rated current maximum300 mA
    SRF minimum320 MHz
    Test frequency50 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11103

    Mechanical Drawing

    MCQ1V2012-R047-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11103: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    Where a circuit needs a small, stable inductance in a package measured in millimetres, the multilayer chip is the default. Its self-resonant frequency is the practical ceiling – above it the part behaves like a capacitor, so the SRF column is the first thing to check against the operating band.

    The row reads 0.047 nH ±10 with a minimum Q of 25 at 50 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 25 means the part’s loss is about 4 % of its reactance in that band.

    Self-resonance is quoted as 320 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 320 MHz is the design headroom.

    Within the MCQ1V2012 family this is value 1 of 25, in a range that runs from 0.047 to 4.7 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message