Eaton MCQ1V3216-R150-R 0.15 nH Chip Inductor 1206
Eaton MCQ1V3216-R150-R 0.15 nH Chip Inductor 1206

Eaton MCQ1V3216-R150-R 0.15 nH Chip Inductor 1206

Share
MCQ1V3216-R150-R: multilayer chip inductor, 0.15 nH ±10, Q 25, SRF 200 MHz, 250 mA, DCR 250 mOhm.
    • Product Details
    • Download

    Eaton MCQ1V3216-R150-R 0.15 nH Chip Inductor 1206

    MCQ1V3216-R150-R at a glance: multilayer chip inductor, 0.15 nH ±10, Q 25, SRF 200 MHz, 250 mA, DCR 250 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCQ1V3216-R150-R
    Inductance0.15 nH ±10
    Q minimum25
    DCR maximum @ +25 °C250 mOhm
    Rated current maximum250 mA
    SRF minimum200 MHz
    Test frequency25 MHz
    Test voltage50 mV
    Package3.2 x 1.6 mm
    Size code3216 (1206)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11102

    Outline Drawing

    MCQ1V3216-R150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11102: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    A multilayer chip inductor is a coil printed in layers of ceramic and metal, fired into a single body. There is no winding to buzz or shift, the inductance is set by the printed pattern, and the part sits on the board like any other 0402 or 0603 component. That construction is why these parts are used wherever the value is small and the quantity is large.

    The row reads 0.15 nH ±10 with a minimum Q of 25 at 25 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 25 means the part’s loss is about 4 % of its reactance in that band.

    Self-resonance is quoted as 200 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 200 MHz is the design headroom.

    Within the MCQ1V3216 family this is value 7 of 25, in a range that runs from 0.047 to 4.7 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products