Eaton MCQ1V3216-R820-R 0.82 nH SMD Inductor, SRF 100 MHz
Eaton MCQ1V3216-R820-R 0.82 nH SMD Inductor, SRF 100 MHz

Eaton MCQ1V3216-R820-R 0.82 nH SMD Inductor, SRF 100 MHz

Share
MCQ1V3216-R820-R: multilayer chip inductor, 0.82 nH ±10, Q 30, SRF 100 MHz, 150 mA, DCR 600 mOhm.
    • Product Details
    • Download

    Eaton MCQ1V3216-R820-R 0.82 nH SMD Inductor, SRF 100 MHz

    MCQ1V3216-R820-R at a glance: multilayer chip inductor, 0.82 nH ±10, Q 30, SRF 100 MHz, 150 mA, DCR 600 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCQ1V3216-R820-R
    Inductance0.82 nH ±10
    Q minimum30
    DCR maximum @ +25 °C600 mOhm
    Rated current maximum150 mA
    SRF minimum100 MHz
    Test frequency25 MHz
    Test voltage50 mV
    Package3.2 x 1.6 mm
    Size code3216 (1206)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11102

    Mechanical Drawing

    MCQ1V3216-R820-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11102: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    What the Numbers Mean

    A multilayer chip inductor is a coil printed in layers of ceramic and metal, fired into a single body. There is no winding to buzz or shift, the inductance is set by the printed pattern, and the part sits on the board like any other 0402 or 0603 component. That construction is why these parts are used wherever the value is small and the quantity is large.

    The row reads 0.82 nH ±10 with a minimum Q of 30 at 25 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 30 means the part’s loss is about 3.33 % of its reactance in that band.

    Self-resonance is quoted as 100 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 100 MHz is the design headroom.

    Within the MCQ1V3216 family this is value 16 of 25, in a range that runs from 0.047 to 4.7 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products