Eaton MFBA2V1005P-471-R 470 Ohm Ferrite Bead, 1100 mA
Eaton MFBA2V1005P-471-R 470 Ohm Ferrite Bead, 1100 mA

Eaton MFBA2V1005P-471-R 470 Ohm Ferrite Bead, 1100 mA

Share
MFBA2V1005P-471-R: multilayer ferrite bead, 470 Ohm at 100 MHz, 1100 mA, DCR 180 mOhm.
    • Product Details
    • Download

    Eaton MFBA2V1005P-471-R 470 Ohm Ferrite Bead, 1100 mA

    MFBA2V1005P-471-R at a glance: multilayer ferrite bead, 470 Ohm at 100 MHz, 1100 mA, DCR 180 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMFBA2V1005P-471-R
    Impedance @ 100 MHz470 Ohm
    DCR maximum @ +25 °C180 mOhm
    Rated current maximum1100 mA
    Package1.0 x 0.5 mm
    Size code1005 (0402)
    MountingSurface mount
    Operating temperature-55 °C to +150 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1130

    Mechanical Dimensions & Pad Layout

    MFBA2V1005P-471-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1130: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    Beads are placed in series with a supply or signal line to take the high-frequency edge off it. The rated current and the DCR decide whether the part can sit in a power path; the impedance decides how much noise it removes.

    At 100 MHz this bead presents 470 ohm, and its DC resistance is 180 mOhm maximum. At the rated 1100 mA that resistance drops 0.198 V, which is the figure to check against the rail tolerance.

    Within the MFBA2V1005P family this is value 3 of 4, in a range that runs from 0 to 0 nH.

    Positioning in the Range

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: body electronics (keyless entry, ecu, antennas); advanced driver assistance systems (adas); infotainment and cluster electronics; safety electronics systems; wlan, wifi, bluetooth.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Does the bead dissipate the noise as heat?
    Yes. The ferrite is lossy at the frequencies it absorbs, so the noise energy becomes heat in the material rather than being reflected back to the source.

    Does the bead dissipate the noise as heat?
    Yes. The ferrite is lossy at the frequencies it absorbs, so the noise energy becomes heat in the material rather than being reflected back to the source.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products