Eaton MFBA2V1608P-471-R 470 Ohm Multilayer Chip Bead
Eaton MFBA2V1608P-471-R 470 Ohm Multilayer Chip Bead

Eaton MFBA2V1608P-471-R 470 Ohm Multilayer Chip Bead

Share
MFBA2V1608P-471-R: multilayer ferrite bead, 470 Ohm at 100 MHz, 2000 mA, DCR 90 mOhm.
    • Product Details
    • Download

    Eaton MFBA2V1608P-471-R 470 Ohm Multilayer Chip Bead

    MFBA2V1608P-471-R at a glance: multilayer ferrite bead, 470 Ohm at 100 MHz, 2000 mA, DCR 90 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMFBA2V1608P-471-R
    Impedance @ 100 MHz470 Ohm
    DCR maximum @ +25 °C90 mOhm
    Rated current maximum2000 mA
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-55 °C to +150 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1131

    Dimensions and Pad Layout

    MFBA2V1608P-471-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1131: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 470 ohm, and its DC resistance is 90 mOhm maximum. At the rated 2000 mA that resistance drops 0.18 V, which is the figure to check against the rail tolerance.

    Within the MFBA2V1608P family this is value 4 of 6, in a range that runs from 0 to 0 nH.

    Positioning in the Range

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: body electronics (keyless entry, ecu, antennas); advanced driver assistance systems (adas); infotainment and cluster electronics; safety electronics systems; wlan, wifi, bluetooth.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Does the bead dissipate the noise as heat?
    Yes. The ferrite is lossy at the frequencies it absorbs, so the noise energy becomes heat in the material rather than being reflected back to the source.

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products