Eaton MFBA3V2012K-102-R 1000 Ohm Ferrite Bead 0805
Eaton MFBA3V2012K-102-R 1000 Ohm Ferrite Bead 0805

Eaton MFBA3V2012K-102-R 1000 Ohm Ferrite Bead 0805

Share
MFBA3V2012K-102-R: multilayer ferrite bead, 1000 Ohm at 100 MHz, 400 mA, DCR 450 mOhm.
    • Product Details
    • Download

    Eaton MFBA3V2012K-102-R 1000 Ohm Ferrite Bead 0805

    MFBA3V2012K-102-R at a glance: multilayer ferrite bead, 1000 Ohm at 100 MHz, 400 mA, DCR 450 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMFBA3V2012K-102-R
    Impedance @ 100 MHz1000 Ohm
    DCR maximum @ +25 °C450 mOhm
    Rated current maximum400 mA
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-55 °C to +150 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1329

    Mechanical Drawing

    MFBA3V2012K-102-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1329: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    A ferrite bead is not an inductor in the usual sense: it is a lossy element. At low frequency it looks like a small resistance in series with the line; at the frequency where the ferrite absorbs, its impedance rises and the noise energy is converted into heat in the material rather than reflected back into the circuit.

    At 100 MHz this bead presents 1000 ohm, and its DC resistance is 450 mOhm maximum. At the rated 400 mA that resistance drops 0.18 V, which is the figure to check against the rail tolerance.

    Within the MFBA3V2012K family this is value 11 of 11, in a range that runs from 0 to 0 nH.

    Where This Series Fits

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: body electronics (keyless entry, ecu, antennas); advanced driver assistance systems (adas); infotainment and cluster electronics; safety electronics systems; wlan, wifi, bluetooth.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products