Eaton MFBA3V2012K-110-R 11 Ohm Ferrite Bead, 900 mA
Eaton MFBA3V2012K-110-R 11 Ohm Ferrite Bead, 900 mA

Eaton MFBA3V2012K-110-R 11 Ohm Ferrite Bead, 900 mA

Share
MFBA3V2012K-110-R: multilayer ferrite bead, 11 Ohm at 100 MHz, 900 mA, DCR 100 mOhm.
    • Product Details
    • Download

    Eaton MFBA3V2012K-110-R 11 Ohm Ferrite Bead, 900 mA

    MFBA3V2012K-110-R at a glance: multilayer ferrite bead, 11 Ohm at 100 MHz, 900 mA, DCR 100 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMFBA3V2012K-110-R
    Impedance @ 100 MHz11 Ohm
    DCR maximum @ +25 °C100 mOhm
    Rated current maximum900 mA
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-55 °C to +150 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1329

    Mechanical Dimensions & Pad Layout

    MFBA3V2012K-110-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1329: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 11 ohm, and its DC resistance is 100 mOhm maximum. At the rated 900 mA that resistance drops 0.09 V, which is the figure to check against the rail tolerance.

    Within the MFBA3V2012K family this is value 1 of 11, in a range that runs from 0 to 0 nH.

    What This Family Is For

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: body electronics (keyless entry, ecu, antennas); advanced driver assistance systems (adas); infotainment and cluster electronics; safety electronics systems; wlan, wifi, bluetooth.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products