Eaton MFBM1V1005-190-R 19 Ohm Multilayer Chip Bead
Eaton MFBM1V1005-190-R 19 Ohm Multilayer Chip Bead

Eaton MFBM1V1005-190-R 19 Ohm Multilayer Chip Bead

Share
MFBM1V1005-190-R: multilayer ferrite bead, 19 Ohm at 100 MHz, 1500 mA, DCR 60 mOhm.
    • Product Details
    • Download

    Eaton MFBM1V1005-190-R 19 Ohm Multilayer Chip Bead

    MFBM1V1005-190-R at a glance: multilayer ferrite bead, 19 Ohm at 100 MHz, 1500 mA, DCR 60 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMFBM1V1005-190-R
    Impedance @ 100 MHz19 Ohm
    Impedance tolerance12~25 Ω
    DCR maximum @ +25 °C60 mOhm
    Rated current maximum1500 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package1.0 x 0.5 mm
    Size code1005 (0402)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11110

    Outline Drawing

    MFBM1V1005-190-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11110: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 19 ohm with an allowed spread of 12~25 Ω, and its DC resistance is 60 mOhm maximum. At the rated 1500 mA that resistance drops 0.09 V, which is the figure to check against the rail tolerance.

    Within the MFBM1V1005 family this is value 7 of 21, in a range that runs from 0 to 0 nH.

    Where This Series Fits

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antennas.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Does the bead dissipate the noise as heat?
    Yes. The ferrite is lossy at the frequencies it absorbs, so the noise energy becomes heat in the material rather than being reflected back to the source.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products