Eaton MFBM1V2012-601-R 600 Ohm SMD Bead, 2000 mA
Eaton MFBM1V2012-601-R 600 Ohm SMD Bead, 2000 mA

Eaton MFBM1V2012-601-R 600 Ohm SMD Bead, 2000 mA

Share
MFBM1V2012-601-R: multilayer ferrite bead, 600 Ohm at 100 MHz, 2000 mA, DCR 100 mOhm.
    • Product Details
    • Download

    Eaton MFBM1V2012-601-R 600 Ohm SMD Bead, 2000 mA

    MFBM1V2012-601-R at a glance: multilayer ferrite bead, 600 Ohm at 100 MHz, 2000 mA, DCR 100 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMFBM1V2012-601-R
    Impedance @ 100 MHz600 Ohm
    Impedance tolerance±25%
    DCR maximum @ +25 °C100 mOhm
    Rated current maximum2000 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11112

    Outline Drawing

    MFBM1V2012-601-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11112: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 600 ohm with an allowed spread of ±25%, and its DC resistance is 100 mOhm maximum. At the rated 2000 mA that resistance drops 0.2 V, which is the figure to check against the rail tolerance.

    Within the MFBM1V2012 family this is value 21 of 22, in a range that runs from 0 to 0 nH.

    Positioning in the Range

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antennas.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    Does the bead dissipate the noise as heat?
    Yes. The ferrite is lossy at the frequencies it absorbs, so the noise energy becomes heat in the material rather than being reflected back to the source.

    Does the bead dissipate the noise as heat?
    Yes. The ferrite is lossy at the frequencies it absorbs, so the noise energy becomes heat in the material rather than being reflected back to the source.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products