Eaton MFBM1V3216-190-R 19 Ohm SMD Bead, 6000 mA
Eaton MFBM1V3216-190-R 19 Ohm SMD Bead, 6000 mA

Eaton MFBM1V3216-190-R 19 Ohm SMD Bead, 6000 mA

Share
MFBM1V3216-190-R: multilayer ferrite bead, 19 Ohm at 100 MHz, 6000 mA, DCR 15 mOhm.
    • Product Details
    • Download

    Eaton MFBM1V3216-190-R 19 Ohm SMD Bead, 6000 mA

    MFBM1V3216-190-R at a glance: multilayer ferrite bead, 19 Ohm at 100 MHz, 6000 mA, DCR 15 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMFBM1V3216-190-R
    Impedance @ 100 MHz19 Ohm
    Impedance tolerance12~25 Ω
    DCR maximum @ +25 °C15 mOhm
    Rated current maximum6000 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package3.2 x 1.6 mm
    Size code3216 (1206)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11113

    Mechanical Drawing

    MFBM1V3216-190-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11113: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 19 ohm with an allowed spread of 12~25 Ω, and its DC resistance is 15 mOhm maximum. At the rated 6000 mA that resistance drops 0.09 V, which is the figure to check against the rail tolerance.

    Within the MFBM1V3216 family this is value 7 of 25, in a range that runs from 0 to 0 nH.

    Series Positioning

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antennas.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products