Eaton MFBW1V2012-050-R 5 Ohm Multilayer Chip Bead
Eaton MFBW1V2012-050-R 5 Ohm Multilayer Chip Bead

Eaton MFBW1V2012-050-R 5 Ohm Multilayer Chip Bead

Share
MFBW1V2012-050-R: multilayer ferrite bead, 5 Ohm at 100 MHz, 3000 mA, DCR 30 mOhm.
    • Product Details
    • Download

    Eaton MFBW1V2012-050-R 5 Ohm Multilayer Chip Bead

    MFBW1V2012-050-R at a glance: multilayer ferrite bead, 5 Ohm at 100 MHz, 3000 mA, DCR 30 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMFBW1V2012-050-R
    Impedance @ 100 MHz5 Ohm
    Impedance tolerance0~15 Ω
    DCR maximum @ +25 °C30 mOhm
    Rated current maximum3000 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11108

    Mechanical Dimensions & Pad Layout

    MFBW1V2012-050-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11108: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    The number on the label is impedance at 100 MHz, in ohms. That single figure is what most designs are specified against, but the shape of the impedance curve around it is what actually decides whether the bead kills a 30 MHz switching harmonic or only the 300 MHz edge.

    At 100 MHz this bead presents 5 ohm with an allowed spread of 0~15 Ω, and its DC resistance is 30 mOhm maximum. At the rated 3000 mA that resistance drops 0.09 V, which is the figure to check against the rail tolerance.

    Within the MFBW1V2012 family this is value 2 of 27, in a range that runs from 0 to 0 nH.

    What This Family Is For

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Does the bead dissipate the noise as heat?
    Yes. The ferrite is lossy at the frequencies it absorbs, so the noise energy becomes heat in the material rather than being reflected back to the source.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products