Eaton MLVA04V05C270-R Multilayer Varistor, 28 V Clamp
Eaton MLVA04V05C270-R Multilayer Varistor, 28 V Clamp

Eaton MLVA04V05C270-R Multilayer Varistor, 28 V Clamp

Share
MLVA04V05C270-R: multilayer varistor ESD suppressor, 8-18 V varistor voltage, 5.5 V working, 28 V clamp, 270 pF, 0.05 J.
    • Product Details
    • Download

    Eaton MLVA04V05C270-R Multilayer Varistor, 28 V Clamp

    MLVA04V05C270-R at a glance: multilayer varistor ESD suppressor, 8-18 V varistor voltage, 5.5 V working, 28 V clamp, 270 pF, 0.05 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMLVA04V05C270-R
    Package size0402
    Working voltage, RMS4 Vrms
    Working voltage, DC5.5 Vdc
    Varistor voltage at 1 mA8-18 V
    Clamping voltage28 V
    Typical capacitance270 pF
    Peak current20 A
    Transient energy0.05 J
    Package0402 (1005 metric)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 10493

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    A chip varistor is a ceramic body with two metal terminations, so it looks like a capacitor and behaves like one until the transient arrives. That is why the capacitance column is quoted on every page: it is the parameter that decides whether the part can sit on a data line.

    The clamp column works out at 3.5 times the varistor voltage: 28 V at the rated current against 8-18 V at 1 mA. That ratio is what the downstream part has to survive, not the 8-18 V figure on the label.

    The 270 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVA-R family this is item 4 of 10 in the Eaton catalogue.

    Positioning in the Range

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • A varistor is not a zener. It has no sharp knee, so it conducts a little at the working voltage and the leakage column is the honest measure of that.
    • These parts are halogen free and RoHS compliant without exemptions, which matters for automotive and appliance programmes.

    Frequently Asked Questions

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products