Eaton MLVB04V18C003 18 V Multilayer Varistor
Eaton MLVB04V18C003 18 V Multilayer Varistor

Eaton MLVB04V18C003 18 V Multilayer Varistor

Share
MLVB04V18C003: multilayer varistor ESD suppressor, 22-34 V varistor voltage, 18 V working, 58 V clamp, 3 pF.
    • Product Details
    • Download

    Eaton MLVB04V18C003 18 V Multilayer Varistor

    MLVB04V18C003 at a glance: multilayer varistor ESD suppressor, 22-34 V varistor voltage, 18 V working, 58 V clamp, 3 pF.

    Electrical Specifications

    ParameterValue
    Orderable part numberMLVB04V18C003
    Package size0402
    Working voltage, DC18 Vdc
    Varistor voltage at 1 mA22-34 V
    Clamping voltage58 V
    Typical capacitance3 pF
    Leakage currentmax. 10 uA
    Package0402 (1005 metric)
    MountingSurface mount
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 4071

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    A chip varistor is a ceramic body with two metal terminations, so it looks like a capacitor and behaves like one until the transient arrives. That is why the capacitance column is quoted on every page: it is the parameter that decides whether the part can sit on a data line.

    The clamp column works out at 2.64 times the varistor voltage: 58 V at the rated current against 22-34 V at 1 mA. That ratio is what the downstream part has to survive, not the 22-34 V figure on the label.

    Standing at 18 V the leakage is at most 10 uA, which is 0.18 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 3 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVB family this is item 3 of 8 in the Eaton catalogue.

    Where This Series Fits

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • The energy rating assumes a single pulse. Repeating the same transient heats the body faster than the datasheet curve suggests, because the curve is drawn for one event at a time.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    Why is the DC rating lower than the AC rating on some parts?
    It is not, on these: the AC rating is an RMS value, so the DC rating is set at the peak of that sine plus margin. Where the two look inconsistent, check which one is quoted as RMS.

    Can it protect a differential pair?
    Only with a low-capacitance part and a layout that keeps both lines symmetric. A single varistor from each line to ground is normal; one across the pair is not, because it unbalances the pair.

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products