Eaton MLVC12V033C180 Multilayer Varistor, 79 V Clamp
Eaton MLVC12V033C180 Multilayer Varistor, 79 V Clamp

Eaton MLVC12V033C180 Multilayer Varistor, 79 V Clamp

Share
MLVC12V033C180: multilayer varistor ESD suppressor, 45 V varistor voltage, 33 V working, 79 V clamp, 180 pF, 0.1 J.
    • Product Details
    • Download

    Eaton MLVC12V033C180 Multilayer Varistor, 79 V Clamp

    MLVC12V033C180 at a glance: multilayer varistor ESD suppressor, 45 V varistor voltage, 33 V working, 79 V clamp, 180 pF, 0.1 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMLVC12V033C180
    Working voltage, DC33 Vdc
    Working voltage, AC23.3 Vac
    Varistor voltage at 1 mA45 V ±10%
    Clamping voltage at 1 A79 V
    Energy absorption, 10/1000 us0.1 J
    Peak current, 8/20 us35 A
    Typical capacitance at 1 MHz180 pF
    Package1206 (3216 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11237

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    The Figures Explained

    A chip varistor is a ceramic body with two metal terminations, so it looks like a capacitor and behaves like one until the transient arrives. That is why the capacitance column is quoted on every page: it is the parameter that decides whether the part can sit on a data line.

    The clamp column works out at 1.76 times the varistor voltage: 79 V at the rated current against 45 V at 1 mA. That ratio is what the downstream part has to survive, not the 45 V figure on the label.

    The 180 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC general type family this is item 34 of 41 in the Eaton catalogue.

    Where This Series Fits

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • The energy rating assumes a single pulse. Repeating the same transient heats the body faster than the datasheet curve suggests, because the curve is drawn for one event at a time.
    • The varistor voltage tolerance is wide by design. Two parts of the same part number can differ by 20 percent and both be good, so the design has to work at the low end of the range.

    Frequently Asked Questions

    Why is the DC rating lower than the AC rating on some parts?
    It is not, on these: the AC rating is an RMS value, so the DC rating is set at the peak of that sine plus margin. Where the two look inconsistent, check which one is quoted as RMS.

    Can it protect a differential pair?
    Only with a low-capacitance part and a layout that keeps both lines symmetric. A single varistor from each line to ground is normal; one across the pair is not, because it unbalances the pair.

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products