Eaton MLVC12V065C100 MLV ESD Suppressor 100 pF
Eaton MLVC12V065C100 MLV ESD Suppressor 100 pF

Eaton MLVC12V065C100 MLV ESD Suppressor 100 pF

Share
MLVC12V065C100: multilayer varistor ESD suppressor, 82 V varistor voltage, 65 V working, 144 V clamp, 100 pF, 0.1 J.
    • Product Details
    • Download

    Eaton MLVC12V065C100 MLV ESD Suppressor 100 pF

    MLVC12V065C100 at a glance: multilayer varistor ESD suppressor, 82 V varistor voltage, 65 V working, 144 V clamp, 100 pF, 0.1 J.

    Specification Table

    ParameterValue
    Orderable part numberMLVC12V065C100
    Working voltage, DC65 Vdc
    Working voltage, AC46 Vac
    Varistor voltage at 1 mA82 V ±10%
    Clamping voltage at 1 A144 V
    Energy absorption, 10/1000 us0.1 J
    Peak current, 8/20 us35 A
    Typical capacitance at 1 MHz100 pF
    Package1206 (3216 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11237

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    The Figures Explained

    These parts are zinc oxide ceramics sintered into a chip, so the response is faster than a junction device and there is no wear-out mechanism below the rated energy. What does degrade them is repeated energy above the rating, which shows up as a falling varistor voltage.

    The clamp column works out at 1.76 times the varistor voltage: 144 V at the rated current against 82 V at 1 mA. That ratio is what the downstream part has to survive, not the 82 V figure on the label.

    The 100 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC general type family this is item 40 of 41 in the Eaton catalogue.

    Where This Series Fits

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not run the part at its varistor voltage: the working voltage column is the continuous limit, and the varistor voltage is 1.5 to 2 times higher only because the ceramic is soft at the knee.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products