Eaton MLVC18V011C2400 1812 Chip Varistor 11 Vdc
Eaton MLVC18V011C2400 1812 Chip Varistor 11 Vdc

Eaton MLVC18V011C2400 1812 Chip Varistor 11 Vdc

Share
MLVC18V011C2400: multilayer varistor ESD suppressor, 16 V varistor voltage, 11 V working, 33 V clamp, 2400 pF, 2.5 J.
    • Product Details
    • Download

    Eaton MLVC18V011C2400 1812 Chip Varistor 11 Vdc

    MLVC18V011C2400 at a glance: multilayer varistor ESD suppressor, 16 V varistor voltage, 11 V working, 33 V clamp, 2400 pF, 2.5 J.

    Key Specifications

    ParameterValue
    Orderable part numberMLVC18V011C2400
    Working voltage, DC11 Vdc
    Working voltage, AC7.8 Vac
    Varistor voltage at 1 mA16 V ±15%
    Clamping voltage at 1 A33 V
    Energy absorption, 10/1000 us2.5 J
    Peak current, 8/20 us500 A
    Typical capacitance at 1 MHz2400 pF
    Package1812 (4532 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    In a multilayer construction the zinc oxide grains are stacked in many thin layers, so the same body height gives a higher voltage per unit area than a single-layer disc. That is how an 0402 chip reaches 18 Vdc working voltage without becoming thick.

    The clamp column works out at 2.06 times the varistor voltage: 33 V at the rated current against 16 V at 1 mA. That ratio is what the downstream part has to survive, not the 16 V figure on the label.

    The 2400 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 40 of 97 in the Eaton catalogue.

    Positioning in the Range

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not use a varistor as a series element or in a signal path carrying DC. It is a shunt device, and any steady current through it is a fault.
    • These parts are halogen free and RoHS compliant without exemptions, which matters for automotive and appliance programmes.

    Frequently Asked Questions

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Does the clamp voltage scale with the surge current?
    Yes. The clamp column is quoted at a stated current, usually 1 A. At ten times that current the residual voltage is higher, so read the V-I curve rather than the single number when the surge is large.

    Why is the DC rating lower than the AC rating on some parts?
    It is not, on these: the AC rating is an RMS value, so the DC rating is set at the peak of that sine plus margin. Where the two look inconsistent, check which one is quoted as RMS.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products