Eaton MLVC18V018C1800 1812 Chip Varistor 18 Vdc
Eaton MLVC18V018C1800 1812 Chip Varistor 18 Vdc

Eaton MLVC18V018C1800 1812 Chip Varistor 18 Vdc

Share
MLVC18V018C1800: multilayer varistor ESD suppressor, 25 V varistor voltage, 18 V working, 44 V clamp, 1800 pF, 2.5 J.
    • Product Details
    • Download

    Eaton MLVC18V018C1800 1812 Chip Varistor 18 Vdc

    MLVC18V018C1800 at a glance: multilayer varistor ESD suppressor, 25 V varistor voltage, 18 V working, 44 V clamp, 1800 pF, 2.5 J.

    Key Specifications

    ParameterValue
    Orderable part numberMLVC18V018C1800
    Working voltage, DC18 Vdc
    Working voltage, AC12.7 Vac
    Varistor voltage at 1 mA25 V ±10%
    Clamping voltage at 1 A44 V
    Energy absorption, 10/1000 us2.5 J
    Peak current, 8/20 us500 A
    Typical capacitance at 1 MHz1800 pF
    Package1812 (4532 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    A chip varistor is a ceramic body with two metal terminations, so it looks like a capacitor and behaves like one until the transient arrives. That is why the capacitance column is quoted on every page: it is the parameter that decides whether the part can sit on a data line.

    The clamp column works out at 1.76 times the varistor voltage: 44 V at the rated current against 25 V at 1 mA. That ratio is what the downstream part has to survive, not the 25 V figure on the label.

    The 1800 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 44 of 97 in the Eaton catalogue.

    Series Positioning

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not run the part at its varistor voltage: the working voltage column is the continuous limit, and the varistor voltage is 1.5 to 2 times higher only because the ceramic is soft at the knee.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products