Eaton MLVC22V068C700 68 V Multilayer Varistor
Eaton MLVC22V068C700 68 V Multilayer Varistor

Eaton MLVC22V068C700 68 V Multilayer Varistor

Share
MLVC22V068C700: multilayer varistor ESD suppressor, 86 V varistor voltage, 68 V working, 151 V clamp, 700 pF, 2.5 J.
    • Product Details
    • Download

    Eaton MLVC22V068C700 68 V Multilayer Varistor

    MLVC22V068C700 at a glance: multilayer varistor ESD suppressor, 86 V varistor voltage, 68 V working, 151 V clamp, 700 pF, 2.5 J.

    Specification Table

    ParameterValue
    Orderable part numberMLVC22V068C700
    Working voltage, DC68 Vdc
    Working voltage, AC48 Vac
    Varistor voltage at 1 mA86 V ±10%
    Clamping voltage at 1 A151 V
    Energy absorption, 10/1000 us2.5 J
    Peak current, 8/20 us600 A
    Typical capacitance at 1 MHz700 pF
    Package2220 (5750 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    The Figures Explained

    In a multilayer construction the zinc oxide grains are stacked in many thin layers, so the same body height gives a higher voltage per unit area than a single-layer disc. That is how an 0402 chip reaches 18 Vdc working voltage without becoming thick.

    The clamp column works out at 1.76 times the varistor voltage: 151 V at the rated current against 86 V at 1 mA. That ratio is what the downstream part has to survive, not the 86 V figure on the label.

    The 700 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 66 of 97 in the Eaton catalogue.

    Where This Series Fits

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • The energy rating assumes a single pulse. Repeating the same transient heats the body faster than the datasheet curve suggests, because the curve is drawn for one event at a time.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message