Eaton MLVC32V031C2200 31 V Multilayer Varistor
Eaton MLVC32V031C2200 31 V Multilayer Varistor

Eaton MLVC32V031C2200 31 V Multilayer Varistor

Share
MLVC32V031C2200: multilayer varistor ESD suppressor, 39 V varistor voltage, 31 V working, 69 V clamp, 2200 pF, 0.7 J.
    • Product Details
    • Download

    Eaton MLVC32V031C2200 31 V Multilayer Varistor

    MLVC32V031C2200 at a glance: multilayer varistor ESD suppressor, 39 V varistor voltage, 31 V working, 69 V clamp, 2200 pF, 0.7 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMLVC32V031C2200
    Working voltage, DC31 Vdc
    Working voltage, AC25 Vac
    Varistor voltage at 1 mA39 V ±10%
    Clamping voltage at 1 A69 V
    Energy absorption, 10/1000 us0.7 J
    Peak current, 8/20 us100 A
    Typical capacitance at 1 MHz2200 pF
    Package3225 (8063 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    A chip varistor is a ceramic body with two metal terminations, so it looks like a capacitor and behaves like one until the transient arrives. That is why the capacitance column is quoted on every page: it is the parameter that decides whether the part can sit on a data line.

    The clamp column works out at 1.77 times the varistor voltage: 69 V at the rated current against 39 V at 1 mA. That ratio is what the downstream part has to survive, not the 39 V figure on the label.

    The 2200 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 70 of 97 in the Eaton catalogue.

    Series Positioning

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • Do not run the part at its varistor voltage: the working voltage column is the continuous limit, and the varistor voltage is 1.5 to 2 times higher only because the ceramic is soft at the knee.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    Why is the DC rating lower than the AC rating on some parts?
    It is not, on these: the AC rating is an RMS value, so the DC rating is set at the peak of that sine plus margin. Where the two look inconsistent, check which one is quoted as RMS.

    Can it protect a differential pair?
    Only with a low-capacitance part and a layout that keeps both lines symmetric. A single varistor from each line to ground is normal; one across the pair is not, because it unbalances the pair.

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products