Eaton MLVC40V180C800 4032 Chip Varistor 180 Vdc
Eaton MLVC40V180C800 4032 Chip Varistor 180 Vdc

Eaton MLVC40V180C800 4032 Chip Varistor 180 Vdc

Share
MLVC40V180C800: multilayer varistor ESD suppressor, 220 V varistor voltage, 180 V working, 387 V clamp, 800 pF, 10 J.
    • Product Details
    • Download

    Eaton MLVC40V180C800 4032 Chip Varistor 180 Vdc

    MLVC40V180C800 at a glance: multilayer varistor ESD suppressor, 220 V varistor voltage, 180 V working, 387 V clamp, 800 pF, 10 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMLVC40V180C800
    Working voltage, DC180 Vdc
    Working voltage, AC140 Vac
    Varistor voltage at 1 mA220 V ±10%
    Clamping voltage at 1 A387 V
    Energy absorption, 10/1000 us10 J
    Peak current, 8/20 us1200 A
    Typical capacitance at 1 MHz800 pF
    Package4032 (10280 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    A multilayer varistor sits across a signal or supply rail and does nothing until the voltage crosses its breakdown point, at which it turns into a low impedance and diverts the transient. The value that matters for the protected chip is not the varistor voltage but the clamping voltage at the surge current you expect.

    The clamp column works out at 1.76 times the varistor voltage: 387 V at the rated current against 220 V at 1 mA. That ratio is what the downstream part has to survive, not the 220 V figure on the label.

    The 800 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 96 of 97 in the Eaton catalogue.

    What This Family Is For

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not use a varistor as a series element or in a signal path carrying DC. It is a shunt device, and any steady current through it is a fault.
    • The varistor voltage tolerance is wide by design. Two parts of the same part number can differ by 20 percent and both be good, so the design has to work at the low end of the range.

    Frequently Asked Questions

    Why is the DC rating lower than the AC rating on some parts?
    It is not, on these: the AC rating is an RMS value, so the DC rating is set at the peak of that sine plus margin. Where the two look inconsistent, check which one is quoted as RMS.

    Can it protect a differential pair?
    Only with a low-capacitance part and a layout that keeps both lines symmetric. A single varistor from each line to ground is normal; one across the pair is not, because it unbalances the pair.

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message