Eaton MLVHV0806V175 0806 chip Chip Varistor 225 Vdc
Eaton MLVHV0806V175 0806 chip Chip Varistor 225 Vdc

Eaton MLVHV0806V175 0806 chip Chip Varistor 225 Vdc

Share
MLVHV0806V175: multilayer varistor ESD suppressor, 270 V varistor voltage, 225 V working, 390 V clamp, 100 pF.
    • Product Details
    • Download

    Eaton MLVHV0806V175 0806 chip Chip Varistor 225 Vdc

    MLVHV0806V175 at a glance: multilayer varistor ESD suppressor, 270 V varistor voltage, 225 V working, 390 V clamp, 100 pF.

    Specification Table

    ParameterValue
    Orderable part numberMLVHV0806V175
    Working voltage, AC175 Vac
    Working voltage, DC225 Vdc
    Varistor voltage at 1 mA270 V ±10%
    Leakage current at 0.8 Vvmax. 80 uA
    Clamping voltage at 1 A390 V
    Typical capacitance at 1 kHz100 pF
    Peak current, 8/20 us (1 pulse)100 A
    Peak current, 8/20 us (15 pulses)50 A
    Package0806 chip
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1239

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    The Figures Explained

    In a multilayer construction the zinc oxide grains are stacked in many thin layers, so the same body height gives a higher voltage per unit area than a single-layer disc. That is how an 0402 chip reaches 18 Vdc working voltage without becoming thick.

    The clamp column works out at 1.44 times the varistor voltage: 390 V at the rated current against 270 V at 1 mA. That ratio is what the downstream part has to survive, not the 270 V figure on the label.

    Standing at 225 V the leakage is at most 80 uA, which is 18 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 100 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVHV family this is item 3 of 5 in the Eaton catalogue.

    Where This Series Fits

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • The energy rating assumes a single pulse. Repeating the same transient heats the body faster than the datasheet curve suggests, because the curve is drawn for one event at a time.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products