Eaton MOV07V190 MOV Disc Varistor 7 mm
Eaton MOV07V190 MOV Disc Varistor 7 mm

Eaton MOV07V190 MOV Disc Varistor 7 mm

Share
MOV07V190: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 165 pF, 20 J.
    • Product Details
    • Download

    Eaton MOV07V190 MOV Disc Varistor 7 mm

    MOV07V190 at a glance: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 165 pF, 20 J.

    Specification Table

    ParameterValue
    Orderable part numberMOV07V190
    Varistor voltage at 1 mA300 V
    Maximum continuous AC voltage190 Vrms
    Maximum continuous DC voltage250 Vdc
    Clamping voltage500 V
    Clamping current10 A
    Maximum surge current, 8/20 us1200 A
    Rated power0.25 W
    Typical capacitance at 1 kHz165 pF
    Maximum energy, 10/1000 us20 J
    Maximum body diameter4.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package7 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    The disc is coated in epoxy and marked with the part number and the varistor voltage. Because the body is the component, the lead spacing and the disc diameter together decide the footprint – there is no separate package to shrink around it.

    The clamp column works out at 1.67 times the varistor voltage: 500 V at the rated current against 300 V at 1 mA. That ratio is what the downstream part has to survive, not the 300 V figure on the label.

    The disc absorbs 20 J in a 10/1000 us pulse and carries 1200 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.25 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 165 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 5 of 71 in the Eaton catalogue.

    Positioning in the Range

    Mount it with the body clear of the transformer and the bridge rectifier; a disc running at its rated power needs air, and the derating curve assumes it gets some.

    • Do not put a varistor across a DC bus without checking the follow current: at DC there is no zero crossing to extinguish it, and the disc can overheat after the surge has passed.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    Why is the DC rating higher than the AC rating?
    The AC rating is an RMS value, so the peak of the sine is 1.41 times higher. The DC rating is set at that peak plus margin, which is why a 130 Vac part is rated 170 Vdc.

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products