Eaton MOV07V510 Radial MOV, 1200 A Surge
Eaton MOV07V510 Radial MOV, 1200 A Surge

Eaton MOV07V510 Radial MOV, 1200 A Surge

Share
MOV07V510: radial leaded metal oxide varistor, 820 V varistor voltage, 670 V working, 1355 V clamp, 60 pF, 52 J.
    • Product Details
    • Download

    Eaton MOV07V510 Radial MOV, 1200 A Surge

    MOV07V510 at a glance: radial leaded metal oxide varistor, 820 V varistor voltage, 670 V working, 1355 V clamp, 60 pF, 52 J.

    Specification Table

    ParameterValue
    Orderable part numberMOV07V510
    Varistor voltage at 1 mA820 V
    Maximum continuous AC voltage510 Vrms
    Maximum continuous DC voltage670 Vdc
    Clamping voltage1355 V
    Clamping current10 A
    Maximum surge current, 8/20 us1200 A
    Rated power0.25 W
    Typical capacitance at 1 kHz60 pF
    Maximum energy, 10/1000 us52 J
    Maximum body diameter6.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package7 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    In a surge event the varistor goes from megohms to ohms in nanoseconds and takes the current the source can deliver. What limits it is the energy in the pulse and the number of pulses, not the peak current alone: the 8/20 test is a single shot.

    The clamp column works out at 1.65 times the varistor voltage: 1355 V at the rated current against 820 V at 1 mA. That ratio is what the downstream part has to survive, not the 820 V figure on the label.

    The disc absorbs 52 J in a 10/1000 us pulse and carries 1200 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.25 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 60 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 15 of 71 in the Eaton catalogue.

    Positioning in the Range

    Keep the leads short and do not sleeve them together: the loop area between the two leads is part of the clamping path, and folding them against each other is what keeps the inductance low.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • Disc diameter sets both the energy and the lead spacing. A 20 mm part needs a 7.5 mm hole pitch, so the footprint decision comes before the electrical one.

    Frequently Asked Questions

    Why is the DC rating higher than the AC rating?
    The AC rating is an RMS value, so the peak of the sine is 1.41 times higher. The DC rating is set at that peak plus margin, which is why a 130 Vac part is rated 170 Vdc.

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products