Eaton MOV10V190 190 Vac Radial Varistor
Eaton MOV10V190 190 Vac Radial Varistor

Eaton MOV10V190 190 Vac Radial Varistor

Share
MOV10V190: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 330 pF, 40 J.
    • Product Details
    • Download

    Eaton MOV10V190 190 Vac Radial Varistor

    MOV10V190 at a glance: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 330 pF, 40 J.

    Specification Table

    ParameterValue
    Orderable part numberMOV10V190
    Varistor voltage at 1 mA300 V
    Maximum continuous AC voltage190 Vrms
    Maximum continuous DC voltage250 Vdc
    Clamping voltage500 V
    Clamping current25 A
    Maximum surge current, 8/20 us2500 A
    Rated power0.4 W
    Typical capacitance at 1 kHz330 pF
    Maximum energy, 10/1000 us40 J
    Maximum body diameter5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package10 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    A radial disc varistor is the mains-side workhorse: it absorbs the surge that comes down the line and clamps it below the withstand of what follows. The selection is a chain of three numbers – continuous voltage, varistor voltage and energy – and the disc diameter sets all three.

    The clamp column works out at 1.67 times the varistor voltage: 500 V at the rated current against 300 V at 1 mA. That ratio is what the downstream part has to survive, not the 300 V figure on the label.

    The disc absorbs 40 J in a 10/1000 us pulse and carries 2500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.4 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 330 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 20 of 71 in the Eaton catalogue.

    What This Family Is For

    Mount it with the body clear of the transformer and the bridge rectifier; a disc running at its rated power needs air, and the derating curve assumes it gets some.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • The derating curve starts at 85 °C for most discs: above that the rated power falls linearly to zero at the maximum temperature.

    Frequently Asked Questions

    Does the lead spacing matter electrically?
    It matters mechanically and for inductance. Wider spacing means a larger loop, which adds inductance in series with the clamp; the disc diameter sets the spacing, so the two choices are linked.

    What is the rated power for?
    It is the continuous dissipation the disc can take at 85 °C ambient. It matters when the varistor sits at a voltage close to its knee, not during the surge.

    Are these parts UL recognised?
    Yes, the data sheet lists cURus to UL 1449 and TUV. The file numbers are on the agency page of the data sheet, and they cover the whole family.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products