Eaton MOV10V250 Radial MOV, 2500 A Surge
Eaton MOV10V250 Radial MOV, 2500 A Surge

Eaton MOV10V250 Radial MOV, 2500 A Surge

Share
MOV10V250: radial leaded metal oxide varistor, 390 V varistor voltage, 320 V working, 650 V clamp, 260 pF, 60 J.
    • Product Details
    • Download

    Eaton MOV10V250 Radial MOV, 2500 A Surge

    MOV10V250 at a glance: radial leaded metal oxide varistor, 390 V varistor voltage, 320 V working, 650 V clamp, 260 pF, 60 J.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMOV10V250
    Varistor voltage at 1 mA390 V
    Maximum continuous AC voltage250 Vrms
    Maximum continuous DC voltage320 Vdc
    Clamping voltage650 V
    Clamping current25 A
    Maximum surge current, 8/20 us2500 A
    Rated power0.4 W
    Typical capacitance at 1 kHz260 pF
    Maximum energy, 10/1000 us60 J
    Maximum body diameter5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package10 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    In a surge event the varistor goes from megohms to ohms in nanoseconds and takes the current the source can deliver. What limits it is the energy in the pulse and the number of pulses, not the peak current alone: the 8/20 test is a single shot.

    The clamp column works out at 1.67 times the varistor voltage: 650 V at the rated current against 390 V at 1 mA. That ratio is what the downstream part has to survive, not the 390 V figure on the label.

    The disc absorbs 60 J in a 10/1000 us pulse and carries 2500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.4 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 260 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 23 of 71 in the Eaton catalogue.

    Positioning in the Range

    Keep the leads short and do not sleeve them together: the loop area between the two leads is part of the clamping path, and folding them against each other is what keeps the inductance low.

    • Do not put a varistor across a DC bus without checking the follow current: at DC there is no zero crossing to extinguish it, and the disc can overheat after the surge has passed.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    Why is the DC rating higher than the AC rating?
    The AC rating is an RMS value, so the peak of the sine is 1.41 times higher. The DC rating is set at that peak plus margin, which is why a 130 Vac part is rated 170 Vdc.

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products