Eaton MOV14V230 230 Vac Radial Varistor
Eaton MOV14V230 230 Vac Radial Varistor

Eaton MOV14V230 230 Vac Radial Varistor

Share
MOV14V230: radial leaded metal oxide varistor, 360 V varistor voltage, 300 V working, 595 V clamp, 560 pF, 93 J.
    • Product Details
    • Download

    Eaton MOV14V230 230 Vac Radial Varistor

    MOV14V230 at a glance: radial leaded metal oxide varistor, 360 V varistor voltage, 300 V working, 595 V clamp, 560 pF, 93 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMOV14V230
    Varistor voltage at 1 mA360 V
    Maximum continuous AC voltage230 Vrms
    Maximum continuous DC voltage300 Vdc
    Clamping voltage595 V
    Clamping current50 A
    Maximum surge current, 8/20 us4500 A
    Rated power0.6 W
    Typical capacitance at 1 kHz560 pF
    Maximum energy, 10/1000 us93 J
    Maximum body diameter5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package14 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    In a surge event the varistor goes from megohms to ohms in nanoseconds and takes the current the source can deliver. What limits it is the energy in the pulse and the number of pulses, not the peak current alone: the 8/20 test is a single shot.

    The clamp column works out at 1.65 times the varistor voltage: 595 V at the rated current against 360 V at 1 mA. That ratio is what the downstream part has to survive, not the 360 V figure on the label.

    The disc absorbs 93 J in a 10/1000 us pulse and carries 4500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.6 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 560 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 40 of 71 in the Eaton catalogue.

    Positioning in the Range

    The varistor sits across the input after the fuse and before the rectifier, with short, thick traces or a direct lead-to-terminal connection. A long return path turns the trace inductance into a voltage spike that the varistor cannot clamp.

    • Do not put a varistor across a DC bus without checking the follow current: at DC there is no zero crossing to extinguish it, and the disc can overheat after the surge has passed.
    • Disc diameter sets both the energy and the lead spacing. A 20 mm part needs a 7.5 mm hole pitch, so the footprint decision comes before the electrical one.

    Frequently Asked Questions

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Does the lead spacing matter electrically?
    It matters mechanically and for inductance. Wider spacing means a larger loop, which adds inductance in series with the clamp; the disc diameter sets the spacing, so the two choices are linked.

    What is the rated power for?
    It is the continuous dissipation the disc can take at 85 °C ambient. It matters when the varistor sits at a voltage close to its knee, not during the surge.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products