Eaton MOV14V625 Radial MOV, 4500 A Surge
Eaton MOV14V625 Radial MOV, 4500 A Surge

Eaton MOV14V625 Radial MOV, 4500 A Surge

Share
MOV14V625: radial leaded metal oxide varistor, 1000 V varistor voltage, 825 V working, 1650 V clamp, 200 pF, 190 J.
    • Product Details
    • Download

    Eaton MOV14V625 Radial MOV, 4500 A Surge

    MOV14V625 at a glance: radial leaded metal oxide varistor, 1000 V varistor voltage, 825 V working, 1650 V clamp, 200 pF, 190 J.

    Key Specifications

    ParameterValue
    Orderable part numberMOV14V625
    Varistor voltage at 1 mA1000 V
    Maximum continuous AC voltage625 Vrms
    Maximum continuous DC voltage825 Vdc
    Clamping voltage1650 V
    Clamping current50 A
    Maximum surge current, 8/20 us4500 A
    Rated power0.6 W
    Typical capacitance at 1 kHz200 pF
    Maximum energy, 10/1000 us190 J
    Maximum body diameter7.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package14 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    The disc is a sintered zinc oxide body with a silver electrode on each face and two tinned leads. Energy absorption scales with the volume of the body, which is why a 20 mm part takes several times the joule rating of a 7 mm part at the same varistor voltage.

    The clamp column works out at 1.65 times the varistor voltage: 1650 V at the rated current against 1000 V at 1 mA. That ratio is what the downstream part has to survive, not the 1000 V figure on the label.

    The disc absorbs 190 J in a 10/1000 us pulse and carries 4500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.6 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 200 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 51 of 71 in the Eaton catalogue.

    Positioning in the Range

    The varistor sits across the input after the fuse and before the rectifier, with short, thick traces or a direct lead-to-terminal connection. A long return path turns the trace inductance into a voltage spike that the varistor cannot clamp.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products