Eaton MOV20V190 190 Vac Radial Varistor
Eaton MOV20V190 190 Vac Radial Varistor

Eaton MOV20V190 190 Vac Radial Varistor

Share
MOV20V190: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 1300 pF, 136 J.
    • Product Details
    • Download

    Eaton MOV20V190 190 Vac Radial Varistor

    MOV20V190 at a glance: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 1300 pF, 136 J.

    Specification Table

    ParameterValue
    Orderable part numberMOV20V190
    Varistor voltage at 1 mA300 V
    Maximum continuous AC voltage190 Vrms
    Maximum continuous DC voltage250 Vdc
    Clamping voltage500 V
    Clamping current100 A
    Maximum surge current, 8/20 us6500 A
    Rated power1 W
    Typical capacitance at 1 kHz1300 pF
    Maximum energy, 10/1000 us136 J
    Maximum body diameter5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    In a surge event the varistor goes from megohms to ohms in nanoseconds and takes the current the source can deliver. What limits it is the energy in the pulse and the number of pulses, not the peak current alone: the 8/20 test is a single shot.

    The clamp column works out at 1.67 times the varistor voltage: 500 V at the rated current against 300 V at 1 mA. That ratio is what the downstream part has to survive, not the 300 V figure on the label.

    The disc absorbs 136 J in a 10/1000 us pulse and carries 6500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 1 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 1300 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 56 of 71 in the Eaton catalogue.

    Positioning in the Range

    The varistor sits across the input after the fuse and before the rectifier, with short, thick traces or a direct lead-to-terminal connection. A long return path turns the trace inductance into a voltage spike that the varistor cannot clamp.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    Does the lead spacing matter electrically?
    It matters mechanically and for inductance. Wider spacing means a larger loop, which adds inductance in series with the clamp; the disc diameter sets the spacing, so the two choices are linked.

    What is the rated power for?
    It is the continuous dissipation the disc can take at 85 °C ambient. It matters when the varistor sits at a voltage close to its knee, not during the surge.

    Are these parts UL recognised?
    Yes, the data sheet lists cURus to UL 1449 and TUV. The file numbers are on the agency page of the data sheet, and they cover the whole family.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products