Eaton MOV20V510 510 Vac Radial Varistor
Eaton MOV20V510 510 Vac Radial Varistor

Eaton MOV20V510 510 Vac Radial Varistor

Share
MOV20V510: radial leaded metal oxide varistor, 820 V varistor voltage, 670 V working, 1355 V clamp, 500 pF, 282 J.
    • Product Details
    • Download

    Eaton MOV20V510 510 Vac Radial Varistor

    MOV20V510 at a glance: radial leaded metal oxide varistor, 820 V varistor voltage, 670 V working, 1355 V clamp, 500 pF, 282 J.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMOV20V510
    Varistor voltage at 1 mA820 V
    Maximum continuous AC voltage510 Vrms
    Maximum continuous DC voltage670 Vdc
    Clamping voltage1355 V
    Clamping current100 A
    Maximum surge current, 8/20 us6500 A
    Rated power1 W
    Typical capacitance at 1 kHz500 pF
    Maximum energy, 10/1000 us282 J
    Maximum body diameter7.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    A radial disc varistor is the mains-side workhorse: it absorbs the surge that comes down the line and clamps it below the withstand of what follows. The selection is a chain of three numbers – continuous voltage, varistor voltage and energy – and the disc diameter sets all three.

    The clamp column works out at 1.65 times the varistor voltage: 1355 V at the rated current against 820 V at 1 mA. That ratio is what the downstream part has to survive, not the 820 V figure on the label.

    The disc absorbs 282 J in a 10/1000 us pulse and carries 6500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 1 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 500 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 68 of 71 in the Eaton catalogue.

    Positioning in the Range

    The varistor sits across the input after the fuse and before the rectifier, with short, thick traces or a direct lead-to-terminal connection. A long return path turns the trace inductance into a voltage spike that the varistor cannot clamp.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    Why is the DC rating higher than the AC rating?
    The AC rating is an RMS value, so the peak of the sine is 1.41 times higher. The DC rating is set at that peak plus margin, which is why a 130 Vac part is rated 170 Vdc.

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products