Eaton MOVGT07V075K Coordinated MOV + GDT, 1020 V
Eaton MOVGT07V075K Coordinated MOV + GDT, 1020 V

Eaton MOVGT07V075K Coordinated MOV + GDT, 1020 V

Share
MOVGT07V075K: integrated MOV / GDT device, 1020 V clamp, 5 pF, 12.5 J.
    • Product Details
    • Download

    Eaton MOVGT07V075K Coordinated MOV + GDT, 1020 V

    MOVGT07V075K at a glance: integrated MOV / GDT device, 1020 V clamp, 5 pF, 12.5 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMOVGT07V075K
    UL volts65 Vac
    Recommended MCOV80 Vac
    UL MCOV85 Vac
    MOV voltage at 1 mA100(90~110) V
    GDT voltage at 100 V/s350(280~420) V
    Platform voltage at 1000 V/usmax. 180 V
    Peak voltage at 1000 V/usmax. 1020 V
    Withstand count at 2 kV / 1 kA40 shots
    MOV withstand current, 8/20 us1750 A
    Maximum energy, 10/1000 us12.5 J
    Capacitance at 1 kHz5 pF
    Package7 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +105 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1161

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    This is a mains-input protector, not a board-level one. It is chosen for the first stage ahead of a differential filter, and its platform voltage is what the downstream 1 kV-rated parts have to survive.

    The MOV inside is a 100(90~110) V part and the GDT is a 350(280~420) V tube. In series the pair holds the surge at the platform voltage of 180 V, well under the peak 1020 V it would reach alone at a 1000 V/us edge.

    Withstand is quoted as 40 shots at 2 kV / 1 kA. Because the GDT carries the follow current, the MOV is not eroded by the long tail of the pulse the way a stand-alone varistor is.

    Within the MOVGT family this is item 4 of 160 in the Eaton catalogue.

    What This Family Is For

    The series combination goes across the input at the first stage, ahead of the filter, with the GDT on the line side. Both devices carry the surge current, so the trace between them has to be as short and as wide as the incoming conductor.

    • The series stack needs the MOV to hold off the line at the end of life as well. If the MOV degrades low in voltage the GDT starts to see the line, which is why the withstand count matters.
    • The platform voltage is the level the combination holds during the surge; size the downstream insulation against it, not against the GDT DC sparkover.

    Frequently Asked Questions

    Does the GDT need a separate fuse?
    The follow current is limited by the source impedance and the upstream fuse. Check that the fuse clears the follow current, otherwise the tube keeps conducting after the surge.

    Is the capacitance low enough for a signal line?
    A few picofarads, yes, but this is a mains protector. Its package and its platform voltage are chosen for an input stage, not for a data pair.

    Why put a GDT in series with a MOV?
    The MOV triggers fast and the GDT clamps low. In series the MOV starts the conduction and the GDT carries the current, so the residual voltage is closer to the GDT arc voltage than to the MOV clamp.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products