Eaton MOVHE10V550 Radial MOV, 3500 A Surge
Eaton MOVHE10V550 Radial MOV, 3500 A Surge

Eaton MOVHE10V550 Radial MOV, 3500 A Surge

Share
MOVHE10V550: radial leaded metal oxide varistor, 910 V varistor voltage, 745 V working, 1500 V clamp, 110 pF, 130 J.
    • Product Details
    • Download

    Eaton MOVHE10V550 Radial MOV, 3500 A Surge

    MOVHE10V550 at a glance: radial leaded metal oxide varistor, 910 V varistor voltage, 745 V working, 1500 V clamp, 110 pF, 130 J.

    Key Specifications

    ParameterValue
    Orderable part numberMOVHE10V550
    Varistor voltage at 1 mA910 V
    Maximum continuous AC voltage550 Vrms
    Maximum continuous DC voltage745 Vdc
    Clamping voltage1500 V
    Clamping current25 A
    Maximum surge current, 8/20 us3500 A
    Rated power0.4 W
    Typical capacitance at 1 kHz110 pF
    Maximum energy, 10/1000 us130 J
    Maximum body diameter7.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package10 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1288

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    For AC mains service the continuous rating is given as an RMS voltage, and the DC rating is that value multiplied by roughly 1.41. Sizing the part at or near the nominal line voltage leaves no room for regulation tolerance or a prolonged overvoltage, so the usual rule is 10 to 20 percent headroom.

    The clamp column works out at 1.65 times the varistor voltage: 1500 V at the rated current against 910 V at 1 mA. That ratio is what the downstream part has to survive, not the 910 V figure on the label.

    The disc absorbs 130 J in a 10/1000 us pulse and carries 3500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.4 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 110 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOVHE family this is item 32 of 71 in the Eaton catalogue.

    Series Positioning

    Keep the leads short and do not sleeve them together: the loop area between the two leads is part of the clamping path, and folding them against each other is what keeps the inductance low.

    • A varistor that has failed short looks like a low-value resistor across the line. Always pair a mains varistor with a fuse or a thermal element.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products