Eaton MOVHE20V190 Radial MOV, 10000 A Surge
Eaton MOVHE20V190 Radial MOV, 10000 A Surge

Eaton MOVHE20V190 Radial MOV, 10000 A Surge

Share
MOVHE20V190: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 1300 pF, 210 J.
    • Product Details
    • Download

    Eaton MOVHE20V190 Radial MOV, 10000 A Surge

    MOVHE20V190 at a glance: radial leaded metal oxide varistor, 300 V varistor voltage, 250 V working, 500 V clamp, 1300 pF, 210 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMOVHE20V190
    Varistor voltage at 1 mA300 V
    Maximum continuous AC voltage190 Vrms
    Maximum continuous DC voltage250 Vdc
    Clamping voltage500 V
    Clamping current100 A
    Maximum surge current, 8/20 us10000 A
    Rated power1 W
    Typical capacitance at 1 kHz1300 pF
    Maximum energy, 10/1000 us210 J
    Maximum body diameter5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1288

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    For AC mains service the continuous rating is given as an RMS voltage, and the DC rating is that value multiplied by roughly 1.41. Sizing the part at or near the nominal line voltage leaves no room for regulation tolerance or a prolonged overvoltage, so the usual rule is 10 to 20 percent headroom.

    The clamp column works out at 1.67 times the varistor voltage: 500 V at the rated current against 300 V at 1 mA. That ratio is what the downstream part has to survive, not the 300 V figure on the label.

    The disc absorbs 210 J in a 10/1000 us pulse and carries 10000 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 1 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 1300 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOVHE family this is item 56 of 71 in the Eaton catalogue.

    Where This Series Fits

    Keep the leads short and do not sleeve them together: the loop area between the two leads is part of the clamping path, and folding them against each other is what keeps the inductance low.

    • A varistor that has failed short looks like a low-value resistor across the line. Always pair a mains varistor with a fuse or a thermal element.
    • Disc diameter sets both the energy and the lead spacing. A 20 mm part needs a 7.5 mm hole pitch, so the footprint decision comes before the electrical one.

    Frequently Asked Questions

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products