Eaton MOVS2825V250 SMT Varistor, 400 A Peak
Eaton MOVS2825V250 SMT Varistor, 400 A Peak

Eaton MOVS2825V250 SMT Varistor, 400 A Peak

Share
MOVS2825V250: surface mount metal oxide varistor, 351-429 V varistor voltage, 330 V working, 675 V clamp, 55 pF, 12 J.
    • Product Details
    • Download

    Eaton MOVS2825V250 SMT Varistor, 400 A Peak

    MOVS2825V250 at a glance: surface mount metal oxide varistor, 351-429 V varistor voltage, 330 V working, 675 V clamp, 55 pF, 12 J.

    Key Specifications

    ParameterValue
    Orderable part numberMOVS2825V250
    Working voltage, RMS250 Vrms
    Working voltage, DC330 Vdc
    Varistor voltage at 1 mA351-429 V
    Leakage current at 0.8 Vvmax. 50 uA
    Clamping voltage, 8/20 us675 V
    Peak current, 8/20 us400 A
    Maximum energy, 10/1000 us12 J
    Rated power0.1 W
    Typical capacitance at 1 kHz55 pF
    Component thickness4.2 mm
    Package2825
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1005

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    A surface mount varistor puts the same zinc oxide body into a leadless chip so the protection sits next to the connector on an automated line. The absence of leads removes the inductance that slows a radial part, which matters when the transient has a fast edge.

    The clamp column works out at 1.92 times the varistor voltage: 675 V at the rated current against 351~429 V at 1 mA. That ratio is what the downstream part has to survive, not the 351~429 V figure on the label.

    Standing at 330 V the leakage is at most 50 uA, which is 16.5 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    At 4.2 mm tall this is the part that has to fit under the enclosure. The 12 J rating and the 400 A peak come from a body that size, so a lower profile in the same footprint would mean less energy.

    Within the MOVS2825 family this is item 21 of 27 in the Eaton catalogue.

    What This Family Is For

    Put it before the series ferrite or inductor, on the side that faces the cable. The order of the two components decides which one takes the surge.

    • Do not stack a chip varistor on a via-in-pad without filling it: the solder wicking changes the joint and the thermal path at the same time.
    • The 2825 and 4032 bodies are thick enough that the pick-and-place nozzle needs the right tip; a standard 0402 nozzle will not hold them.

    Frequently Asked Questions

    Why is the capacitance so high?
    A 4032 body at 14 Vdc has a large electrode area and a thin dielectric, so the capacitance runs into thousands of picofarads. That is fine on a supply rail and not fine on a data line.

    Can two parts be paralleled for more energy?
    Only if they are matched, which they are not. The varistor voltage tolerance means one part takes most of the current, so the pair behaves like the weaker one plus a little.

    What is the operating temperature range?
    The table states it for each family; the upper limit is the point where the rated power falls to zero, not the point where the part stops working.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products