Eaton MPI4015V2-R68-R 0.68 uH High-Current Inductor
Eaton MPI4015V2-R68-R 0.68 uH High-Current Inductor

Eaton MPI4015V2-R68-R 0.68 uH High-Current Inductor

Share
MPI4015V2-R68-R: high-current power inductor, 0.68 uH, 6.8 A, Isat 8 A, DCR 16 mOhm.
    • Product Details
    • Download

    Eaton MPI4015V2-R68-R 0.68 uH High-Current Inductor

    MPI4015V2-R68-R at a glance: high-current power inductor, 0.68 uH, 6.8 A, Isat 8 A, DCR 16 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMPI4015V2-R68-R
    Inductance0.68 nH ±20%
    DCR maximum @ +25 °C16 mOhm
    Irms (DC, 40 °C rise)6.8 A
    Isat8 A
    SRF typical19 MHz
    K-factor81
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10651

    Mechanical Drawing

    MPI4015V2-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10651: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a surface-mount power inductor for DC-DC conversion. Its two limiting numbers are Irms, which sets the thermal ceiling, and Isat, which sets the current at which inductance has fallen by a defined percentage – both are on the data sheet row and both matter at different points in the load profile.

    At 6.8 A the winding dissipates about 0.74 W in copper, using the 16 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 8 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the MPI4015V2 family this is value 5 of 12, in a range that runs from 0.22 to 10 uH.

    Series Positioning

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: handheld/mobile devices; portable media players; notebook/netbook/laptop regulators; tablets/smartbooks; battery operated devices.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products