Eaton MPI4040R1-R22-R 0.23 uH Power Inductor, 5.5 A
Eaton MPI4040R1-R22-R 0.23 uH Power Inductor, 5.5 A

Eaton MPI4040R1-R22-R 0.23 uH Power Inductor, 5.5 A

Share
MPI4040R1-R22-R: high-current power inductor, 0.23 uH, 5.5 A, Isat 21 A, DCR 18 mOhm.
    • Product Details
    • Download

    Eaton MPI4040R1-R22-R 0.23 uH Power Inductor, 5.5 A

    MPI4040R1-R22-R at a glance: high-current power inductor, 0.23 uH, 5.5 A, Isat 21 A, DCR 18 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMPI4040R1-R22-R
    Inductance0.23 nH ±20%
    DCR maximum @ +25 °C18 mOhm
    Irms (DC, 40 °C rise)5.5 A
    Isat21 A
    K-factor814
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4086

    Outline Drawing

    MPI4040R1-R22-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4086: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    What the Numbers Mean

    The part is built around a distributed-gap core: the energy is stored through the volume of the magnetic material rather than in a single discrete gap, which is what produces the gradual rolloff and the low fringing field. Copper loss and core loss are traded against each other in the winding and body proportions.

    At 5.5 A the winding dissipates about 0.544 W in copper, using the 18 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 21 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the MPI4040R1 family this is value 3 of 11, in a range that runs from 0.1 to 4.7 uH.

    What This Family Is For

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: handheld/mobile devices; portable media players; gps/pdas; mp3 players; battery operated devices.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message