Eaton MPIA2010V1-1R0-R 1 uH Inductor, Isat 3 A
Eaton MPIA2010V1-1R0-R 1 uH Inductor, Isat 3 A

Eaton MPIA2010V1-1R0-R 1 uH Inductor, Isat 3 A

Share
MPIA2010V1-1R0-R: automotive power inductor, 1 uH , 3 A Irms, Isat 3 A, DCR 56 mOhm.
    • Product Details
    • Download

    Eaton MPIA2010V1-1R0-R 1 uH Inductor, Isat 3 A

    MPIA2010V1-1R0-R at a glance: automotive power inductor, 1 uH , 3 A Irms, Isat 3 A, DCR 56 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMPIA2010V1-1R0-R
    Inductance1 uH
    FLL minimum (at Isat)0.56 uH
    DCR typical @ +20 °C56 mOhm
    DCR maximum @ +20 °C65 mOhm
    Irms (DC, 40 °C rise)3 A
    Isat3 A
    SRF typical100 MHz
    K-factor2771
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1072

    Mechanical Drawing

    MPIA2010V1-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1072: outline with
    rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    A molded automotive power inductor with a soft saturation curve: as current rises the inductance droops instead of collapsing, so a converter keeps control through a load step. The body is molded around the winding, which contains the field.

    At 3 A the winding dissipates about 0.504 W in copper using the typical DCR of 56 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 4.5 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 100 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 2771 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MPIA2010V1 family this is value 3 of 5, in a range from 0.33 uH to 2.2 uH.

    Series Positioning

    The MPIA family is the automotive miniature power range: AEC-Q200 qualified, low profile, in sizes from 2 mm to 4 mm, with both typical and maximum DCR quoted for every row.

    • DCR is quoted at +20 °C; copper rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; doors, window lift and seat control.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three numbers, three checks.

    Frequently Asked Questions

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough for dense layouts.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products