Eaton MPIA2510V3-3R3-R 3.3 uH AEC-Q200 Inductor 140 mOhm
Eaton MPIA2510V3-3R3-R 3.3 uH AEC-Q200 Inductor 140 mOhm

Eaton MPIA2510V3-3R3-R 3.3 uH AEC-Q200 Inductor 140 mOhm

Share
MPIA2510V3-3R3-R: automotive power inductor, 3.3 uH , 1.6 A Irms, Isat 2.1 A, DCR 140 mOhm.
    • Product Details
    • Download

    Eaton MPIA2510V3-3R3-R 3.3 uH AEC-Q200 Inductor 140 mOhm

    MPIA2510V3-3R3-R at a glance: automotive power inductor, 3.3 uH , 1.6 A Irms, Isat 2.1 A, DCR 140 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMPIA2510V3-3R3-R
    Inductance3.3 uH
    FLL minimum (at Isat)1.85 uH
    DCR typical @ +20 °C140 mOhm
    DCR maximum @ +20 °C170 mOhm
    Irms (DC, 40 °C rise)1.6 A
    Isat2.1 A
    SRF typical39 MHz
    K-factor2313
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1487

    Outline Drawing

    MPIA2510V3-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1487: outline with
    rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is a surface-mount power inductor with a distributed-gap core. The energy is stored through the volume of the magnetic material rather than a single gap, which produces the gradual rolloff and keeps the fringing field small.

    At 1.6 A the winding dissipates about 0.358 W in copper using the typical DCR of 140 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 7.28 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 39 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 2313 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MPIA2510V3 family this is value 6 of 7, in a range from 0.47 uH to 4.7 uH.

    Series Positioning

    The MPIA family is the automotive miniature power range: AEC-Q200 qualified, low profile, in sizes from 2 mm to 4 mm, with both typical and maximum DCR quoted for every row.

    • DCR is quoted at +20 °C; copper rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; doors, window lift and seat control.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three numbers, three checks.

    Frequently Asked Questions

    What is the difference between Irms and Isat?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products