Eaton MPIA4015V2-1R0-R 1 uH Shielded Power Inductor
Eaton MPIA4015V2-1R0-R 1 uH Shielded Power Inductor

Eaton MPIA4015V2-1R0-R 1 uH Shielded Power Inductor

Share
MPIA4015V2-1R0-R: automotive power inductor, 1 uH , 5.5 A Irms, Isat 6 A, DCR 23 mOhm.
    • Product Details
    • Download

    Eaton MPIA4015V2-1R0-R 1 uH Shielded Power Inductor

    MPIA4015V2-1R0-R at a glance: automotive power inductor, 1 uH , 5.5 A Irms, Isat 6 A, DCR 23 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMPIA4015V2-1R0-R
    Inductance1 uH
    DCR typical @ +20 °C23 mOhm
    Irms (DC, 40 °C rise)5.5 A
    Isat6 A
    SRF typical27 MHz
    K-factor56
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10652

    Dimensions and Pad Layout

    MPIA4015V2-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10652: outline with
    rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is a surface-mount power inductor with a distributed-gap core. The energy is stored through the volume of the magnetic material rather than a single gap, which produces the gradual rolloff and keeps the fringing field small.

    At 5.5 A the winding dissipates about 0.696 W in copper using the typical DCR of 23 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 18 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 27 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 56 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MPIA4015V2 family this is value 6 of 12, in a range from 0.22 uH to 10 uH.

    Series Positioning

    The MPIA family is the automotive miniature power range: AEC-Q200 qualified, low profile, in sizes from 2 mm to 4 mm, with both typical and maximum DCR quoted for every row.

    • DCR is quoted at +20 °C; copper rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; doors, window lift and seat control.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three numbers, three checks.

    Frequently Asked Questions

    What is the difference between Irms and Isat?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products