Eaton MPIA4040R2-2R2-R 2.2 uH Shielded Power Inductor
Eaton MPIA4040R2-2R2-R 2.2 uH Shielded Power Inductor

Eaton MPIA4040R2-2R2-R 2.2 uH Shielded Power Inductor

Share
MPIA4040R2-2R2-R: automotive power inductor, 2.2 uH , 3.2 A Irms, Isat 5.7 A, DCR 58 mOhm.
    • Product Details
    • Download

    Eaton MPIA4040R2-2R2-R 2.2 uH Shielded Power Inductor

    MPIA4040R2-2R2-R at a glance: automotive power inductor, 2.2 uH , 3.2 A Irms, Isat 5.7 A, DCR 58 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMPIA4040R2-2R2-R
    Inductance2.2 uH
    DCR typical @ +20 °C58 mOhm
    Irms (DC, 40 °C rise)3.2 A
    Isat5.7 A
    K-factor647
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10230

    Mechanical Dimensions & Pad Layout

    MPIA4040R2-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10230: outline with
    rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    A molded automotive power inductor with a soft saturation curve: as current rises the inductance droops instead of collapsing, so a converter keeps control through a load step. The body is molded around the winding, which contains the field.

    At 3.2 A the winding dissipates about 0.594 W in copper using the typical DCR of 58 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 35.7 uJ at the saturation point, which is the energy available to bridge a load step.

    The K-factor of 647 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MPIA4040R2 family this is value 4 of 7, in a range from 0.47 uH to 6.8 uH.

    Series Positioning

    The MPIA family is the automotive miniature power range: AEC-Q200 qualified, low profile, in sizes from 2 mm to 4 mm, with both typical and maximum DCR quoted for every row.

    • DCR is quoted at +20 °C; copper rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: body electronics – central body control module – vehicle access control system – headlamps, tail lamps and interior lighting – door control; chassis and safety electronics – airbag control unit.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three numbers, three checks.

    Frequently Asked Questions

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    What is the difference between Irms and Isat?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products