Eaton MTA2V3029L-2R2-R 2.2 uH Molded Inductor, 85 A
Eaton MTA2V3029L-2R2-R 2.2 uH Molded Inductor, 85 A

Eaton MTA2V3029L-2R2-R 2.2 uH Molded Inductor, 85 A

Share
MTA2V3029L-2R2-R: molded through-hole power inductor, 2.2 uH , 85 A Irms, Isat 95 A, DCR 0.32 mOhm.
    • Product Details
    • Download

    Eaton MTA2V3029L-2R2-R 2.2 uH Molded Inductor, 85 A

    MTA2V3029L-2R2-R at a glance: molded through-hole power inductor, 2.2 uH , 85 A Irms, Isat 95 A, DCR 0.32 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMTA2V3029L-2R2-R
    Inductance2.2 uH
    FLL minimum (at Isat)1.41 uH
    DCR typical @ +20 °C0.32 mOhm
    DCR maximum @ +20 °C0.37 mOhm
    Irms (DC, 40 °C rise)85 A
    Irms297 A
    Isat95 A
    Isat2125 A
    SRF typical25.5 MHz
    K-factor18.1
    MountingThrough-hole
    Operating temperature-55 °C to +155 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1402

    Dimensions and Pad Layout

    MTA2V3029L-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1402: outline with
    rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    Through-hole mounting here is a thermal decision as much as a mechanical one: the leads take the heat into the copper, and the body can be larger than a reflow part because there is no standoff constraint.

    At 85 A the winding dissipates about 2.31 W in copper using the typical DCR of 0.32 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 9928 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 25.5 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 18.1 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MTA2V3029L family this is value 1 of 2, in a range from 2.2 uH to 3 uH.

    Where This Series Fits

    The MTA family is the molded through-hole high-current range: AEC-Q200 qualified, with two Irms and two Isat columns for thermal and transient checks.

    • Through-hole joints carry the full current. Check the solder joint and barrel against the rating, not just the body.
    • Typical applications: infotainment and cluster electronics; audio subsystem: head unit and trunk amp; digital instrument cluster; electronic stability control system (esc); engine and powertrain systems.
    • Design note: check the joint temperature in the thermal test, not the body temperature.

    Frequently Asked Questions

    What is the SRF column for?
    It marks where the winding capacitance takes over. Keep the switching frequency and its harmonics below it.

    Why two Irms and two Isat columns?
    The datasheet gives both a typical and a maximum condition for each limit, so the thermal and the transient margins can be checked against the worst case.

    Why through-hole for this current level?
    The leads carry heat into the board copper and the body is not limited by reflow standoff, which is how the part reaches its current rating.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products