Eaton MTA3V3944S-2R2-R 2.2 uH Molded Inductor, 140 A
Eaton MTA3V3944S-2R2-R 2.2 uH Molded Inductor, 140 A

Eaton MTA3V3944S-2R2-R 2.2 uH Molded Inductor, 140 A

Share
MTA3V3944S-2R2-R: molded through-hole power inductor, 2.2 uH , 140 A Irms, Isat 120 A, DCR 0.21 mOhm.
    • Product Details
    • Download

    Eaton MTA3V3944S-2R2-R 2.2 uH Molded Inductor, 140 A

    MTA3V3944S-2R2-R at a glance: molded through-hole power inductor, 2.2 uH , 140 A Irms, Isat 120 A, DCR 0.21 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMTA3V3944S-2R2-R
    Inductance2.2 uH
    FLL minimum (at Isat)1.23 uH
    DCR typical @ +20 °C0.21 mOhm
    DCR maximum @ +20 °C0.24 mOhm
    Irms (DC, 40 °C rise)140 A
    Isat120 A
    SRF typical18.2 MHz
    K-factor14.8
    MountingThrough-hole
    Operating temperature-55 °C to +155 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1530

    Dimensions and Pad Layout

    MTA3V3944S-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1530: outline with
    rated mm dimensions, pad layout and marking.

    The Figures Explained

    This is an automotive high-current molded inductor with through-hole terminals. The data sheet quotes two Irms columns and two Isat columns, which lets the thermal and the transient limits be checked independently.

    At 140 A the winding dissipates about 4.12 W in copper using the typical DCR of 0.21 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 15840 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 18.2 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 14.8 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MTA3V3944S family this is value 2 of 2, in a range from 1.5 uH to 2.2 uH.

    Where This Series Fits

    The MTA family is the molded through-hole high-current range: AEC-Q200 qualified, with two Irms and two Isat columns for thermal and transient checks.

    • Through-hole joints carry the full current. Check the solder joint and barrel against the rating, not just the body.
    • Typical applications: digital instrument cluster; electronic stability control system (esc); engine and powertrain systems; electric pumps, motor control and auxiliaries; powertrain control unit (pcu)/engine control unit (ecu).
    • Design note: check the joint temperature in the thermal test, not the body temperature.

    Frequently Asked Questions

    Why through-hole for this current level?
    The leads carry heat into the board copper and the body is not limited by reflow standoff, which is how the part reaches its current rating.

    Why two Irms and two Isat columns?
    The datasheet gives both a typical and a maximum condition for each limit, so the thermal and the transient margins can be checked against the worst case.

    Why through-hole for this current level?
    The leads carry heat into the board copper and the body is not limited by reflow standoff, which is how the part reaches its current rating.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products