Eaton SS-5-6.3A-AP 6.3 A 250 Vac Time-Delay Subminiature Fuse
Eaton SS-5-6.3A-AP 6.3 A 250 Vac Time-Delay Subminiature Fuse

Eaton SS-5-6.3A-AP 6.3 A 250 Vac Time-Delay Subminiature Fuse

Share
Eaton SS-5-6.3A-AP is a 6.3 A 250 Vac time-delay subminiature radial fuse, 63 A breaking, 176 A2s I2t.
    • Product Details
    • Download

    Eaton SS-5-6.3A-AP 6.3 A 250 Vac Time-Delay Subminiature Fuse

    SS-5-6.3A-AP at a glance: 176 A2s melting integral, 7.4 mOhm at 20 C, 63 A breaking at 250 Vac - compact rectangular body, saves board area.

    Key Ratings

    ParameterValue
    Orderable part numberSS-5-6.3A-AP (-AP = 1,000 pcs ammo pack, 12.7 mm pitch)
    Current6.3 A
    Typical DC cold resistance7.4 mOhm
    Melting I2t (typical)176 A2s
    CharacteristicTime-delay (T)
    Dissipation at rating0.37 W
    AgencyUL E19180 (JDYX2/JDYX8) / VDE 40015513 / CCC / KC / SEMKO / PSE+JET
    Interrupting rating63 A at rated voltage, 50 Hz
    BodyRadial leaded, time-delay, rectangular, plastic cap and base, UL 94V0
    Design standardIEC 60127-3 sheet 4
    Un (rated)250 Vac
    Voltage drop (typical)59 mV at rated current

    At 6.3 A

    • Board fit. Radial thru-hole, 5.08 mm lead spacing, plastic cap and base rated UL 94V0. It can go straight into the PCB or into a BK/PCS socket if field replacement matters.
    • Where the heat goes. Expect about 0.37 W at 6.3 A. The 7.4 mOhm figure is a 20 C measurement; in a sealed adapter the element runs hotter, so derate rather than assume.
    • Breaking. 63 A is low-breaking-capacity by design - it is a board-level part for primary and secondary protection inside equipment, not a panel fuse.
    • Surge budget. A 2 x 6.3 A, 5 ms pulse consumes 0.45 % of the 176 A2s melting integral. Repeated starts are fine at that level.
    • Above 2 A. At 6.3 A the element is thicker and the I2t climbs to 176 A2s. That is real inrush tolerance, but it also means the part protects the wiring rather than a semiconductor downstream.
    • Top of range. SS-5-5A-AP is the step below at 5 A. Above 6.3 A the breaking capacity of this body stops being enough and the ceramic series takes over.

    For Procurement

    • Order SS-5-6.3A-AP - -AP is 1,000 pieces in an ammo pack at 12.7 mm pitch. -BK is 200 in a polybag (4.3 mm leads), -BK2 200 with 21 mm leads.
    • Approvals: UL E19180 (JDYX2/JDYX8) / VDE 40015513 / CCC / KC / SEMKO / PSE+JET.
    • The purchasing code carries the packaging suffix; the bare part number is not a complete order line.
    • Same element as the cartridge equivalent in this current - only the termination differs.

    Common Questions

    Is the whole part number required?
    Yes. Eaton's ordering code includes the packaging suffix - the bare rating is not a complete order line.

    How hot does it run?
    About 0.37 W at rated current, from 59 mV drop. In a sealed enclosure the derating curve applies.

    Can it go in a socket?
    Yes - the BK/PCS holder takes it if field replacement is wanted. Otherwise it sits directly in the PCB.

    Design note: values are typical unless identified as ratings. Verify the current Eaton data sheet 2621 before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message