Eaton STS321070U162 ESD Suppressor 7 V 165 pF
Eaton STS321070U162 ESD Suppressor 7 V 165 pF

Eaton STS321070U162 ESD Suppressor 7 V 165 pF

Share
STS321070U162: 7 V standoff TVS diode array, 1-channel, 165 pF per line, SOD-323 (S32), commercial grade.
    • Product Details
    • Download

    Eaton STS321070U162 ESD Suppressor 7 V 165 pF

    STS321070U162 at a glance: TVS diode array ESD suppressor, 7 V standoff, 20 V clamp, 1 channel, 165 pF.

    Key Specifications

    ParameterValue
    Orderable part numberSTS321070U162
    Standoff voltage (VRWM)7 V
    Breakdown voltage (min / typ / max)7.5 V / 8.5 V / 9 V
    Leakage current at VRWM0.5 uA max
    Clamping voltage at 1 A15 V
    Clamping voltage at 25 A20 V
    Junction capacitance at 1 MHz, per line165 pF typ / 200 pF max
    Channels1
    PolarityUnidirectional
    ESD capability, IEC 61000-4-2+/-30 kV contact / +/-30 kV air
    PackageSOD-323 (S32)
    MountingSurface mount
    Moisture sensitivity levelMSL 3
    Operating junction temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11152

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data 11152. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    What the Numbers Mean

    Array parts are chosen last, after the connector pinout is fixed. The pin that carries the discharge has to reach the array before it reaches the transceiver, and the ground pin of the array has to be the same copper the connector shell ties to.

    At 25 A the clamp sits at 20 V, or 2.86 times the 7 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet.

    165 pF per line is 0.96 ohms of reactance at 1 GHz and 9.6 ohms at 100 MHz. A real load on a fast line: this grade fits a slow bus or a DC rail, not a high speed data pair.

    Standing at 7 V the part draws at most 0.5 uA, which is 3.5 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    The capacitance in the table is per line, measured at 1 MHz with zero bias. On a differential pair that capacitance sits across the pair and to ground, which is why the low-capacitance grades exist: the same clamp with a fraction of the loading.

    Where It Goes on the Board

    Keep the return current under the signal. A discharge leaves through the ground pin, and if that current has to cross the board to find a plane it will couple into everything it passes on the way.

    • A unidirectional array clamps one polarity at the breakdown and the other at a forward drop. That asymmetry is correct on a DC rail and wrong on a differential pair that swings below ground.
    • The capacitance figure is at zero bias. At the working voltage the junction depletes and the value falls, so the loading on a live bus is lower than the table suggests.

    Frequently Asked Questions

    Why does the clamp voltage differ from the breakdown voltage?
    Breakdown is measured at 1 mA. The clamp is measured at the pulse current, which can be tens of amps, and the difference is the dynamic resistance of the junction multiplied by that current.

    Can one package protect several lines?
    Yes, that is what the channel count means. The lines share a common ground pin, so the return current of all channels flows through one connection and the clamps track each other during the event.

    How many of these parts survive repeated strikes?
    The IEC 61000-4-2 rating is a qualification level, not a life count. The part is expected to take the strike repeatedly at the rated level because the energy per event is small, but a higher level shortens that life.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message