Eaton STS321120U901 ESD Suppressor 12 V 90 pF
Eaton STS321120U901 ESD Suppressor 12 V 90 pF

Eaton STS321120U901 ESD Suppressor 12 V 90 pF

Share
STS321120U901: 12 V standoff TVS diode array, 1-channel, 90 pF per line, SOD-323 (S32), commercial grade.
    • Product Details
    • Download

    Eaton STS321120U901 ESD Suppressor 12 V 90 pF

    STS321120U901 at a glance: TVS diode array ESD suppressor, 12 V standoff, 24 V clamp, 1 channel, 90 pF.

    Ratings at a Glance

    ParameterValue
    Orderable part numberSTS321120U901
    Standoff voltage (VRWM)12 V
    Breakdown voltage (min / typ / max)13.3 V / 13.5 V / 16 V
    Leakage current at VRWM0.1 uA max
    Clamping voltage at 1 A18 V
    Clamping voltage at 15 A24 V
    Junction capacitance at 1 MHz, per line90 pF typ / 100 pF max
    Channels1
    PolarityUnidirectional
    ESD capability, IEC 61000-4-2+/-30 kV contact / +/-30 kV air
    PackageSOD-323 (S32)
    MountingSurface mount
    Moisture sensitivity levelMSL 3
    Operating junction temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11152

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data 11152. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    The Figures Explained

    The capacitance in the table is per line, measured at 1 MHz with zero bias. On a differential pair that capacitance sits across the pair and to ground, which is why the low-capacitance grades exist: the same clamp with a fraction of the loading.

    At 15 A the clamp sits at 24 V, or 2.00 times the 12 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet.

    90 pF per line is 1.8 ohms of reactance at 1 GHz and 17.7 ohms at 100 MHz. A real load on a fast line: this grade fits a slow bus or a DC rail, not a high speed data pair.

    Standing at 12 V the part draws at most 0.1 uA, which is 1.2 uW of dissipation on the line. That is the figure that matters on a battery rail that never powers down.

    The STS series is a diode array in a three to eight pin package: one die per line, all of them sharing a common ground pin. The working voltage is set by the process, not by a resistor divider, so the part either sits above the bus level or it does not belong on that bus at all.

    Placement in the Circuit

    Mount the array on the connector side of any series part, with the ground pin dropped straight into the connector ground plane. The trace from the pin to the array is the only path the discharge takes before the transceiver sees it, so its inductance is part of the clamp.

    • The clamping voltage is quoted at one pulse current. Halve the current and the clamp falls by roughly the dynamic resistance times the current, which is why a part chosen for a small surge looks better than its headline number.
    • Leakage is quoted at the rated voltage and at 25 °C. It roughly doubles every 10 °C, which matters on a rail that sits hot inside an enclosure.

    Frequently Asked Questions

    What happens if the surge exceeds the rating?
    The junction overheats and fails short, which then applies the fault current to the board. A fuse or a series resistor ahead of the array is part of the protection scheme, not an accessory.

    How is the working voltage chosen?
    Above the highest steady state voltage the line can reach, including the fault levels the standard for that interface allows. Then confirm the minimum breakdown voltage is still above that level, because production spread moves it down.

    Why does the package affect the rating?
    It sets the thermal mass and the lead inductance. The same die in a SOD-523 and a SOT-23 dissipates differently, so the package is part of the electrical choice rather than only a footprint decision.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message