Eaton TVSA04V05C006 ESD Suppressor 5 V 6 pF
Eaton TVSA04V05C006 ESD Suppressor 5 V 6 pF

Eaton TVSA04V05C006 ESD Suppressor 5 V 6 pF

Share
TVSA04V05C006: 5 V standoff TVS diode array, 1-channel, 6 pF per line, 0402, commercial grade.
    • Product Details
    • Download

    Eaton TVSA04V05C006 ESD Suppressor 5 V 6 pF

    TVSA04V05C006 at a glance: TVS diode array ESD suppressor, 5 V standoff, 17 V clamp, 1 channel, 6 pF.

    Electrical Specifications

    ParameterValue
    Orderable part numberTVSA04V05C006
    Standoff voltage (VRWM)5 V
    Breakdown voltage (min / typ / max)10 V
    Clamping voltage at 1 A17 V
    Junction capacitance at 1 MHz, per line6 pF typ
    Packaging10,000 pcs per reel
    Channels1
    PolarityBidirectional
    ESD capability, IEC 61000-4-2+/-8 kV contact / +/-15 kV air
    Package0402
    MountingSurface mount
    Moisture sensitivity levelMSL 1
    Operating junction temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data DS4072

    The outline drawing, pad geometry, derating curves and the pulse
    waveform are on the pages of Eaton Technical Data DS4072. Values above are
    read directly from the electrical table for this part number, not from the family
    summary.

    Reading the Data Sheet

    The STS series is a diode array in a three to eight pin package: one die per line, all of them sharing a common ground pin. The working voltage is set by the process, not by a resistor divider, so the part either sits above the bus level or it does not belong on that bus at all.

    At 1 A the clamp sits at 17 V, or 3.40 times the 5 V standoff. The protected pin sees that figure for the duration of the pulse, so it is the one to compare with the absolute maximum in the transceiver data sheet.

    6 pF per line is 26.5 ohms of reactance at 1 GHz and 265 ohms at 100 MHz. Small enough for a bus in the hundreds of kilohertz to a few megahertz, and measurable once the line rate reaches tens of megahertz.

    The capacitance in the table is per line, measured at 1 MHz with zero bias. On a differential pair that capacitance sits across the pair and to ground, which is why the low-capacitance grades exist: the same clamp with a fraction of the loading.

    Layout and Placement

    Mount the array on the connector side of any series part, with the ground pin dropped straight into the connector ground plane. The trace from the pin to the array is the only path the discharge takes before the transceiver sees it, so its inductance is part of the clamp.

    • A unidirectional array clamps one polarity at the breakdown and the other at a forward drop. That asymmetry is correct on a DC rail and wrong on a differential pair that swings below ground.
    • Breakdown is specified at 1 mA. The spread between minimum and maximum is production tolerance, so the design margin is measured from the minimum, not the typical.

    Frequently Asked Questions

    How is the working voltage chosen?
    Above the highest steady state voltage the line can reach, including the fault levels the standard for that interface allows. Then confirm the minimum breakdown voltage is still above that level, because production spread moves it down.

    How many of these parts survive repeated strikes?
    The IEC 61000-4-2 rating is a qualification level, not a life count. The part is expected to take the strike repeatedly at the rated level because the energy per event is small, but a higher level shortens that life.

    Does the array capacitance disturb the signal?
    It loads the line as a capacitor to ground. At 1 pF the reactance is about 160 ohms at 1 GHz and 1.6 kilohms at 100 MHz, which is why the low-capacitance grades are used on high speed pairs and the higher grades on slow buses.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message