Eaton WCL3225-220-R 22 uH Inductor, 200 mA Rated
Eaton WCL3225-220-R 22 uH Inductor, 200 mA Rated

Eaton WCL3225-220-R 22 uH Inductor, 200 mA Rated

Share
WCL3225-220-R: wire wound chip inductor, 22 uH ±5%, Q 10 at 2.52 MHz, 200 mA rated, DCR 2400 mOhm.
    • Product Details
    • Download

    Eaton WCL3225-220-R 22 uH Inductor, 200 mA Rated

    WCL3225-220-R at a glance: wire wound chip inductor, 22 uH ±5%, Q 10 at 2.52 MHz, 200 mA rated, DCR 2400 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberWCL3225-220-R
    OCL22 uH ±5%
    Q minimum @ test frequency10 @ 2.52 MHz
    SRF minimum20 MHz
    DCR maximum @ +25 °C2400 mOhm
    Rated current (20 °C rise)200 mA
    OCL test frequency2.52 MHz
    OCL test voltage500 mV
    Package3.5 x 2.9 mm, 2.25 mm high
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10931

    Mechanical Drawing

    WCL3225-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10931: outline views
    with rated mm dimensions, pad layout and marking.

    How to Read These Ratings

    A wire wound chip inductor is a coil wound on a ceramic or ferrite core with metal end terminals, in a body the size of a resistor. Compared with a multilayer chip of the same size it gives a higher Q and a tighter tolerance, which is why it appears in filters and matching networks rather than only in supply decoupling.

    At the 200 mA rating the winding drops about 480 mV and dissipates 96 mW. Both are small enough to ignore in a bias network but not in a high-Q filter.

    Q of 10 at 2.52 MHz with self-resonance at 20 MHz puts the useful band comfortably below the point where the winding capacitance takes over.

    Within the WCL3225 family this is value 22 of 39, in a range from 0.12 to 560 uH.

    Positioning in the Range

    The WCL and WCLA families run from 1.0 nH in a 1.19 x 0.66 mm body to 560 uH in 3.5 x 2.9 mm, with Q quoted at a stated test frequency for every row.

    • The rated current is a 20 °C rise figure, not a saturation limit. In a DC bias application check the inductance at the actual bias before sizing the filter.
    • Typical applications: industrial connectivity (iot); computing/gaming consoles; smart meters; industrial equipment; machine-to-machine (m2m).
    • Design note: read Q and SRF at the frequency the part works at, not at the test frequency printed in the table.

    Frequently Asked Questions

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    Can I place it with a standard chip shooter?
    Yes, the body and terminals are dimensioned for tape and reel and standard nozzle placement. Check the terminal width against the pad geometry in the drawing.

    How is Q specified?
    At one test frequency, given in the table. Q falls away either side of that point, so a part quoted at 25 MHz tells you little about behaviour at 900 MHz.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message